Monday, February 20, 2012

Welcome, new followers!

Welcome, new followers!  I hope your visits here will prove to informative and perhaps entertaining.

Thanks, for visiting!  And that goes for all.

John

Friday, February 17, 2012

Cold Connect using Micro-Fasteners

A small selection of metal elements using micro fasteners to hold them together.  Screws, washers, nuts.  Brass, copper, aluminum, wire mesh.  Flame patina, various textures.

Photo showing a few of the tools used for micro fastener cold connect.  A few micro fasteners shown by the brush.  When I'm working the tools aren't that neatly placed!

Sunday, February 12, 2012

I posted an entire photo on JewelryLessons. com  and received a comment that it would be nice to have a close-up look at some of the elements.  Rather than hoggong the galley at JL, I'm putting some closer views here.

Tuesday, February 7, 2012

Rolling Mill-Pattern Plates-Disc Cutter-Centering Dies


Shown in the photo are three examples of Bonny Doon Pattern Plate impressions on copper run through the mill.  These are more experimental in nature rather than something actually planned for use in a piece of jewelry.  I can use some areas of the impressions, but some pieces are scratched and will take some work to make the usable.  The examples are on non-annealed 24 gauge copper.  The pattern plates worked out pretty good, but next time I'll run some annealed metal to see how that turns out.  Just couldn't wait any longer. Just had to try out the mill and the pattern plates.

The pattern plates are meant for 24 gauge metal and up to 14 gauge, the max for using a mill.  A hydraulic is better for thinner metal.

Which brings up a point.  When you try a new source of supply for base metal, order only a small amount.  Check the metal when it arrives and if it is scratched, try another source.  One well known supply company whose name I will not divulge, is rather careless in handling their metal stock and scratches, some deep, are the norm.  As a result, they have lost me as a customer.






The photos show The Swanstrom Disc Cutter, the  Center Positioning Dies and some examples of washers cut using the device. 

On the one hand, I'm fairly pleased with the tool.  On the other hand, well for one thing, I think it's over priced.  But, it does make nice washers.  There's a learning curve to using the tool.  Isn't that always the case?

So, you punch a hole in a piece of metal, then use the centering die to center that hole in a larger punch hole to make the washer.  Yup, verrry simple.  Except that a couple things can go wrong.  It's the old "oops!" factor that pops you one in the old snozzola when you're not looking..  You miscalculated and you didn't allow for enough metal for the larger piece, or you allowed for too much metal.

Solution:  Select the outside diameter hole and position the metal for minimum waste, but not too much minimum.  Tighten the tool down just enough to keep it level in the tool.  Select the same size centering die and with a large point Sharpie marker, rub a little ink on the point of the die, drop the die into the hole, and Voila! you have a little dot.   Release the metal from the cutter. Select the inside diameter of the washer to be, and use the dot plus your eyeball. to center the metal in that hole.  Tighten the tool down firmly and punch out the hole.  Move back to the outside diameter hole, insert the centering die and punch out the washer.  No wasted metal.  The tool does deliver a nice clean cut.  

I used a urethane pad under the cutter, Bur Life on the punches and a two pound brass mallet..

Saturday, February 4, 2012

Rolling Mill Idled

No, there's nothing wrong with the mill.  Some things came up and I didn't get the metal sawed and annealed, and readied to run through.  Now, we are getting cold temperatures from the big snowstorm, so no work out in the garage where all the prep work goes on.

I did managed to put together a brace on the mill end of the bench.  This will in turn create place to put a rack to hold some of the heavier hammers.  In fact the whole bench will have to be rearranged in order to create a more sensible flow of work.  Never make anything permanent, sooner or later you'll change it!

In the meantime, work continues putting together more cold connected metal pieces, and refining the process.